The mech is for American notched shafts, using neptonics American shafts.
When the line releases, it also released the spear.
Forgot to mention, I can not get the mech to release incorrectly outside the gun. It's fine on the bench.
Posts by Brendon
-
-
I'm hoping some here that have experience building and tuning mid handle guns can chime im.
After finishing the 2 mid handled 48" guns, I'm having an issue with both guns, both Mechs on releasing early. One actually released in the pool with a band loaded. Please see attached link for video.
After talking with Dan, the issue of preload on the trigger came up. I have the triggers pre loaded up a bit just to remove excess travel but still have a decent length pull before engaging.
Should there not be any preload on the trigger via a pushrod? -
Yeah he really needed a drill press to drill through the bottle cap
-
That's a trip man. Talk about uncalled for. That shark needs some manners.
-
Welcome. I just finished 2 gun builds and the guys here were quite helpful.
-
Very cool footage.
That was a lot of bubble blowers. .
-
For east and west winds I normally say onshore (blowing east to west) or offshore (blowing west to east)... I guess It would be the opposite for the gulf side.
A problem with this is that "on shore" is not always the direction one thinks. On the west coast, a west winds should be onshore right? Unfortunately not. Below central California, the majority of our beaches are south facing. A westerly wind could run 50 miles parallel to the land mass without touching it.
-
I've always thought that the origination direction is what is stated.
A sw wind is actually blowing ne and so on. -
Or a lifeguard in training. .
-
Come to a Neptune meeting,;) The good news when the water cools they may hang half way through winter.
Cheers, Don
I don't know what a Neptune meeting is. Is it a local dive club?
-
The first rule of white sea bass is: You do not talk about white sea bass. The second rule of white sea bass is:
You do not talk about white sea bass. The third rule of white sea bass is: You do not talk about white sea bass.:DCheers, Don
At this point, I've gone 3 years without seeing one. Talking about it can't really make me see any less right?
-
I don't do instagram. I just talk to guys at the shop and on the beach.
Maybe those guys have found them out at the islands. I don't have a boat so it's all beach entries for me -
I've proabably been out on the water 30-40 times this year since June and have yet to comensure upon a single ghost. The hook and line boats had a decent few days earlier this year but have had terrible counts also. We obviously have a lot of yellows that keep it interesting but has anone else noticed a drop off in wsb sightings/harvest this year? Many of the divers I chat with on the beach are noticing the same thing.
I dive from pv through Malibu up to about the ventura jetty. -
Use sharp bits and blades. .
-
The abalone is just decorative. A friend had some abolone flashers he used and they got a lot of attention.
The pad is going to be a definite need. My 5mil suit only gives so much padding. -
Thanks marco. The next gun, I'm actually thinking about running a 5/8 roundover instead of 1/2". Make it a more rounded profile with shorter flats.
-
So what is the fundamental performance difference between a band slot and a dedicated hole? Is it just that you can get another band in the slot if needed?
-
Thanks George.I totally agree with the band slot thing. Definately too vertical. And no. I have not cut any holes for balast. I will do that if it is needed after I confirm with weight and duct tape.
And yeah, baby's definately got back. -
Here are some quick finished pictures of one of the two guns. Finish was 3 liberal coats of watco tung oil followed by 3 coats of General Finishes Arm R Seal.
The gun still needs balasted but I'm going to wait until the second gun is finished and do them at the same time.
I would love to hear HONEST feedback from you guys as I still have another to go and my feelings don't get hurt. If you don't like xy or z, id like to hear it. It a&b would have been best done like this, let me know.This build was really more of a learning experience. Now that it's "done" I don't plan to quit learning. -
Wow guys thanks for all the help! And yes dan ive been planing on coming out there just haven't had a chance too. Ive been doing my research on building a gun for about a month now an i see you guys have some good stuff for a good price.
I just bought two reverse mechs from there. I had a loose spring on one but by and large, the fit and finish is really good. Install was really easy, action is very smooth.