Posts by Dan

Just like you I'm very skeptical of using paint to to make the tubes better. In the long run it may make more trouble than leaving the tubes as they are. If you need to do any glue work, like a patch, I'm pretty sure you'll need to remove the paint as it will not hold glue.

What exactly is expected from a "reconditioning"?

Which part of the RIB?

DO NOT buy a rib with PVC tubes, you want Hypalon tubes. I learned this the hard way. If you don't know how to tell the difference don't buy the boat.

1 x 19mm is plenty powerful, it's fast to load but may be difficult for some divers. 2 x 16mm bands is more power and allows powering down for taking close shots into holes for example. I also like the 2 x 14mm configuration but only with Speardiver small hole or "no hole" bands.

Thanks to Marco for this nice video with the Speardiver Phantom speargun in Panama.

http://www.youtube.com/watch?v=l-k2qyUy-Wc

With this modification the reel will free spool only after the line is pulled hard. Up to that time it will keep tension in the line and hold the spear in place. I explained how to do this modification for those who would prefer a reel to go into free spool as opposed to maintaining consistent pressure on the line. Other than these two options I don't think there's any other way for the reel to function that would necessitate a drag knob in the first place.

Here's a quick and easy way to convert the Speardiver composite reel to a free spooling reel. Unscrew the drag knob retaining bolt, unscrew the drag knob and remove it. Remove the bushing that's under it. Cut the stem of the bushing (1) off with a hacksaw to make it look like (2). Use sand paper or a file to clean up the cut. Install the bushing back in in the reel, screw on the drag knob and retaining bolt. That's it you've got a free spooling reel. If you want to do this but are concerned you may destroy the bushing and render the reel unusable, rest assured I have bushings available separately.

Quote from makoa

Just wanted to comment on the Aimrite. If you cut down the barrel you noticed how thick the wall diameter is. Of all the carbon tubes I've used (including the speardiver barrel) the Super Venom is the thickest measuring 3.5 mm thick!

The new Speardiver C3 Carbon speargun barrel with track has a wall diameter 4mm thick. It's available in lengths from 100cm to 150cm.

The shaft diameter and consequently the power of the speargun should be the first thing you decide on. It's directly related to the kind of hunting you'll be doing/fish you'll be targeting. I take it you'll be bottom hunting with possibility of pelagics passing through?

Will you be using a reel or float line?

Thank you Pete.

The real question is even if everything works as intended does it result in a more powerful/accurate/easy to handle/affordable speargun.

Picture and band configuration for each gun?

Welcome to speardiver.

Glad you like 'em

There's a question in this thread http://spearfishing.world/memb…-spearguns-into-bali.html pertaining your part of the world, perhaps you can help.

Tough luck. Gun looks good though

Some divers consider the red suit ideal, highly visible on the surface, red disappears at depth.

Your wetsuit size is M.

If your foot size is 10.5 then you'll need XL or L socks, depending on how snug you like the fit.

Folding knife is not good, takes too long to open in an emergency situation. You may not appreciate this until you try doing it in cold water with thick gloves. A stiletto point is ideal. I prefer the Speardiver Skene knife for its low profile.

I never did use the small kayak because I have a banks board. I don't see any problem with the small kayak as a float, I'm just not sure if it would actually hold my weight as it is a kids kayak, or what its properties are as a boat. There's also nothing wrong with using a full size kayak, but I find it a lot of work to move around. But then I have a boat.

I can't think of any conditions that would preclude the use of this gun, unless of course you're going after 100lb tuna. The choice you need to make is what length is best suitable for your conditions. I'm no expert on California diving. Here in Florida 110 - 120cm is the go to size.

The Speardiver Phantom is a bullet proof gun. The handle and muzzle are made of a very durable material. The trigger mech, sear, casing and line release are all stainless steel. You can't beat the price and quality. It's also now available with a carbon barrel, if you ever choose to upgrade.